Tips to Program Ford F-150 2019 Key by Autel KM100

Problem:

Using Autopropad G2 andAutel KM100on a F-150 2019 Keyed ignition.
No keypad on door.
Active alarm.
After waiting 10-15 min, alarm beeps twice, then when i add a key the alarm starts beeping again with a note (security authentication failed).
Tried All keys lost.
Tried it under type 10 2017 fusion.
Tried under smart key.
No matter what i do, after the 2 beeps the alarm goes on again.
Any ideas what can be done to program a key?

 

 

Solution:

Here is the tip to program Ford F-150 key with an active alarm.

Common occurrence when all key lost even if no keypad. After you get the double honk, you can always them try the add key, if that fails, do the 10 minute wait time, and then try all keys lost, sometimes that works best.

If add key failed,use Autel all keys lost option.

Put screw driver on the door latch wait 10 minutes when you hear the twice alarm, hit ok.

It will read security and then the alarm will go off again.

Wait for twice alarm them hit ok. It will program the keys since it reads the security first time.
Keep in mind that you have to connect to a running car.
Door latch has to be closed with screw driver until the programming done.

If you have done the screw driver, when it beeps again let it be and wait for 2 beeps again.

Don’t disconnect anything wait for it and then hit ok it will go into programming mode right away.

 

 

OBDSTAR,Xhorseand Auto prog pad also have Ford AKL adapter to bypass active alarm. You can also take theFord FDRS. Even with frds you have to wait the 10 minutes but it goes through from first try.

 

 

User feedback:

Solved withKM100. Sit in the car the whole 10 minutes, skip the open door to power up. I used the KM100 and it worked fine when the Ford was in alarm.

Posted by: jean at 07:29 AM | No Comments | Add Comment
Post contains 337 words, total size 3 kb.

Tips to Program Hyundai Santa Fe 2023+ Smart Key without PIN

Pin reading hit or miss on newer Hyundai/Kia models with aftermarket tools. Some have no support for pincode read at the moment regardless of tool used.

For example, 2023 Kia Rio couldn’t read the pin. Dealer didn’t even have access to the pin. It is crazy that even dealer couldn’t source a pin.

Newer models we had best luck withOBDSTARorVVDI Key Tool Plusif it’s a 8A, 6A chip type. 4A and 47 Autel do great.

 

Quick update for people who may worked or did not work on Hyundai Santa Fe models 2023+. Picture below is a 2023 model that had all keys lost.

 

Successfully done withAutel IM608and no 3rd party pincode retrieval was needed. You can all read via OBD the pincode and either lishi the lock or just remove it for decoding to cut the emergency blade.

 

Lishi that supports keyway KK12 with 7 to 8 cuts. This model has 7 cuts. Have to remove lock because I didn’t have lishi like that in inventory. Easy disassembly and reinstall.

If you plan to get this vehicle done, please note:
-Autel has no universal key option to generate for this car, only until 2022 (TM Version). Car model below is TMA Version.
– Xhorse does have one, but proximity option will not work, but the rest will and only XM38 series is supported (selective few key types). If you get a car like this, luckily AKS and UHS have aftermarket variants that work great. Check with dealer first by VIN the part number and you are all set.
Did Elanta 2023, Sportage 2023, and this one and had no issues.
Good luck out there!

Posted by: jean at 06:40 AM | No Comments | Add Comment
Post contains 285 words, total size 3 kb.

How to Set up DTS Monaco with Godiag GT109 ENET Cable

How to set up Godiag GT109 ENET cable and other ENET DoIP cables with Mercedes Benz DTS Monaco engineering software?

 

You need to connect the ethernet cable to your computer socket and OBD to the car.

 

Then check adapter settings.
Run DTS Monaco software (take example of DTS 8.16)

 

SelectAdministrate and manage DTS projects

 

Check if you already have that settings.

 

Interface name: ENET

Bus System Interface -PDU API
D-PDU API Version: Berner and Mattner Systemtechnick GmbH GDPM_UNITY_FOR_DS_8_16_015
Module Type:MVCI_ISO_13400_DOIP
Vendor Module Name: —-
Cable:CABLE_PART_F_ECOM

– Physical links
IEE_802_3: Ethernet 1

Another configuration works too.

Bus System Interface -PDU API
D-PDU API Version:Softing AG EDIC_D_PDU_API_xx_xx_xxx (any version)
Module Type:MVCI_ISO_13400_DOIP_Collection
Vendor Module Name:—-
Cable:Ethernet_Cable

–Physical links
IEE_802_3:Ethernet 1

Don’t forget to save any changes and we are ready to proceed.

 

Now you can flash modules (head unit, HU5 etc) with the ENET cable.

 

 

Enet cableor Tactrix passthru for DTS Monaco? Which one is faster? And what’s the difference?

Enet connects via DOiP connection (separate wires directly from OBD port to Multimedia) and it’s faster. Especially fast flashing. And only few ECUs (depends on car). All other things like coding could be made by OpenPort or any other J2534 adapter.

Posted by: jean at 07:47 AM | No Comments | Add Comment
Post contains 207 words, total size 6 kb.

How to Fix Lonsdor K518 Pro Failed to Load Error

If yourLonsdor K518 Prostops working and reports error "Failed to load, success to execute App”. Here is the solution.

Solution:

Select ‘Firmware upgrade’ on Settings menu. Update firmware and try again.

 

Posted by: jean at 06:38 AM | No Comments | Add Comment
Post contains 41 words, total size 2 kb.

Will Autel IM508 Program 2021 Nissan Sentra All Keys Lost

Question:

Is it possible to calculate the PIN code for the Nissan Sentra 2021/07? becauseAutel IM508asks for the dynamic code and needs to be recalculated, I’ll attach an example in the photo, but it’s no longer valid, just as an example.

 

 

Solution:

Autel can add key to Nissan Sentra 2021 without pin code. You needNissan 16+32 gateway bypass cable.

Autel and Lonsdor cannot do Sentra 2021 all keys lost. You need pin code from 3rd party.

obdstarcan get the pincode and do all keys lost without pin code (useNissan BCM40 cable)

Posted by: jean at 09:02 AM | No Comments | Add Comment
Post contains 101 words, total size 2 kb.

How to use E-sys to Code Out BMW F20 F30 TPMS

BMW E-sys coding tutorial: how to Code out BMW F20/F30 TPMS back to RPA or RFA.

 

 

To code for no TPMS do the following.

Start the Car engine and leave running throughout

Connect to your car withBMW ENET cable

 

 

Go toExpert ModeTab on left and click onCoding.
PressREADin the top box in the coding screen and then Save when it’s loaded. Call it something like Car FA with TPMS.

 

 

Go to Esys Data folder on you PC and find the folder FA and make a copy of that file and rename one of themWithout TPMS. You should have two files now.

Go back toE-sysand the Editors and Viewers tab and click on FA Editor.

In the top box where it says "File Name” Click on the button with three dots on the right of that text box and open the file you renamed "Without TPMS”.

Right click on the folder FA that appears and Calculate FP
More folders will appear on the right and you can now change the FA.

Expand all the folders by clicking on the little + signs (not header) until you see a folder that says SALAPA Element. click on the folder and your order codes will appear in the bottom box.

Literally go into the SALAPA box at the bottom and delete 2VB (and the comma) and press the little thing that looks like a door with a left arrow in yellow in the right of SALAPA box. (If there is
something wrong there is a red box round the SALAPA box.)

Press the save (Disk) icon at the top toolbar of Esys

 

 

Saving the FA back to the car is not completely necessary (This next bit in VCM)

Go to theExpert ModeTab and click onVCM(You may or may not get a box appear saying there is a file open in the FA-Editor Just press Yes here.)
About two thirds of the way down you will see a box that says "Vehicle Order” with tabs that say File, Master and Backup.
To the right of the box within that says File Name: click on the button with three dots and open your file marked as "Without TPMS”

folders will appear in the top box. Again, Right click on the folder "FA” and Calculate FP
The vehicle profile will be filled in the next box.
Go back to the Vehicle Order box and click on the "Master” tab.

You are now about to write back to the car the new vehicle order back to the car.
Press "Write FA FP” that should only take a second.

 

If you didn’t save the FA to the Car above this is where you start back.

You now have to VO code the ECU’s
In the Expert Mode box go to Coding.
If the top box is populated (Vehicle order) make sure it’s your "Without TPMS”. if not, just press LOAD and load the file in.
When you’ve loaded the correct file Right Click on FA folder and click Activate FP.

Over to the right you will see a box called "SVT Actual”
In that box click on "Read SVT (…”Save this file for a backup (Save button in the same box)

 

 

All your ECU’s will appear in the Big SVT box
(You may not Have NBT as this is ProNav You may have HU..Something and KOMBI is black panel display)
To VO code the ECU’s Scroll down to the ECU’s in the List I gave "DSC NBT ICM KOMBI”
Right click on the yellow folder of the first ECU (DSC) Not the CADF file and press "Code”

Repeat this for the other ECU’s If all goes well you should see this and the words: "Abarbeitung beendet” – finished processing

You will get errors about DTC failure, ABS failure, RDC failure and the clock on the black panel display will need resetting to the correct time.
But that’s it, you’re done! Disconnect and turn the engine on and off to clear spurious warnings.

 

On some US/CAN F30 / F20 it may be necessary to remove fuse #132 found in the rear fusebox in the boot / trunk.

 

As a side note , you can skip writing the FA to the car and do the VO coding alone.

The advantage of writing it though is that if the dealer does an update the car will be coded without the option you removed from the FA so your tpms decoding will stay, else it will get wiped out as the dealer will code the car with the options specified on the FA.

www.obdii365.com

Posted by: jean at 07:03 AM | No Comments | Add Comment
Post contains 772 words, total size 16 kb.

How to Program Nissan Rogue 2022 All Keys Lost Bypass PIN

Here we shared user’s working experience on Nissan Rogue 2022 all smart keys lost.

 

"Made a new key successfully for Nissan Rogue 2022 all keys lost. UsedXhorse XM38series smart key and works great.
Left pictures on what fcc to use, and what settings to write so everything will work. 04 is for remote starter.
Autel IM608+OBDSTAR NISSAN 40 CABLE= WORKS!”

1 plug only. 1 goes to the bcm (obdstar part, the original one connects to the other end of the cable) and then obd.

All the 40-pin cables are the same. You can use OBDSTAR Nissan 40pin gateway cable with OBDStar, XTool, Autel, and Abrites.

Need proper keys. Looks like either oem at the moment or aftermarket with the fcc. Xhorse and autel keys don’t work with remote or proximity. Only if push button to start.

Image attached:

Posted by: jean at 06:37 AM | No Comments | Add Comment
Post contains 149 words, total size 6 kb.

Autel MX808 Registration Authorization Expired Solution

Problem:

Just finished up on a Jeep Gladiator 2020.Autel MX808scanner got codes but cant read. Decoded the vin number. But get this message now. What is the next step? My scanner has been expired since the first of the year.

 

 

Solution:

You need to purchase the Auto Auth subscription to unlock Jeep.

You also need to have active Autel regular subscription.
You need both active subscription and auto authto clear codes or do anything more than just read them.
Auto auth isn’t going to work with an expired subscription on theAutel diagnostic scanners.

If you use the adc2011 and you will not have a problem even with an expired subscription.

How to Purchase, Activate and Use FCA AutoAuth for Autel Scanners?

Posted by: jean at 06:53 AM | No Comments | Add Comment
Post contains 127 words, total size 2 kb.

VNCI VCM3 IDS No License Solution

Ifyour tool isVNCI VCM3 or Genuine VCM3 and you have not ford ids lincese

How to start IDS software without license and let ids work well with your tool?

Step1: you have to install Ford IDS and Ford VCI manager software

Step2: installed VNCI J2534 quickloader software

dowload address: https://mega.nz/file/eKImEBLB#K6ixGnytmEPSG9ojZt12BZlD0InAf8rct93TRHy3gt0

step3: download cracked file and replace VNCI J2534 quickloader executable file with follow .exe files

download address:https://mega.nz/file/yb5GHQ5R#ajVm83W6cwhN3yHuUKIUypkPywSzE4qAyAMRGXGVrDE

Step4: start ids software from quickloader software on your computer desktop, Whether you use VNCI VCM3 or

genuine VCM3 tools, you can run ids software without a license at this time.

Posted by: jean at 07:24 AM | No Comments | Add Comment
Post contains 104 words, total size 1 kb.

Godiag GT109 ENET Cable and BMW ENET Cable Which is Better

What is the difference betweenGodiag GT109 ENET cableand regular BMW ENET cable?

 

 

1. Godiag ENET cable comes with aVoltage indicator. Users will quickly check the current vehicle voltage.

2.Godiag ENET cablehaslow voltage alarmfunction.

If the voltage is lower than 11.5v, it will alarm to remind customers that the voltage is low,the vehicle cannot be started, cannot carry out diagnostic or programming.

The benefits of low voltage alarm:

1).If voltage is low during programming, do not force programming, give a power supply immediately. Especially on BMW cars, low-voltage programming can easily cause module damage.

2). The car has been stored for a long time and the battery can no longer start the vehicle, but some customers still try to start it. In this way, the battery can easily be seriously depleted and scrapped due to forced starting. If the customer receives this prompt to call the police, do not start the vehicle. Start directly with emergency power supply or power supply.

 

The Godiag ENET cable comes to replace the BMW ENET cable. It is cheap,$19.99only.

Godiag cable supports BMW, Benz, VAG, Volvo DoIP models diagnostics, coding and programming with corresponding software.

 

 

Obdii365.comengineer has tested the Godiag ENET cable on VAG MLB and MQB platform. Works without issue.

 

MLBEVO paltform:
A4LB9, Q5L, A6C8, A7,A8D5, Q7 ok
2021 A3L, A5, Q8, E-Tron, Q5etron, Q4 ok
VW ID3 ID4 ID6 ok

MQBEVO platform
2020-2022 Golf 8 ok

2021-2022 TALAGON ok
2020-2022 A3L ok
2021-2022 Teramont ok
2021-2022 Teramont X ok
2021-22 Skoda Octavia Pro ok

Also tested working on the new Bentley, Lamborghini and 2022- Audi models.

 

 

More video guide coming soon.

www.obdii365.com

Posted by: jean at 07:13 AM | No Comments | Add Comment
Post contains 280 words, total size 5 kb.