Launch X431 and PIWIS which for Porsche Macan Coding?

Launch X431 and PIWIS which is better for Porsche Macan Coding?

 

First of all, check Porsche Macan coding capabilities between Launch X431 and PIWIS

LAUNCH X431	PIWIS
Front End Electronics	BCM vorne	Value	Related	Description
WWS Coding	WWS-Codierung
WWS-coding-Teardrop Function active	WWS-Codierung Traenenfunktion aktiv	Yes		Enable automatic delayed extra wipe to clean windshield
Coding
Coding_0
Coding-Comfort functions-Window comfort opening		Yes		Enable automatic window roll down by pressing and holding unlock on keyfob
Coding-Comfort functions-Window comfort closing		Yes		Enable automatic window roll up by pressing and holding lock on keyfob
Coding-Comfort functions-Roof system comfort opening		Yes		Enable automatic sunroof open by pressing and holding unlock on keyfob
Coding-Comfort functions-Roof system comfort closing		Yes		Enable automatic sunroof closing by pressing and holding unlock on keyfob
Exterior lighting DRL with marker light	Außenbeleuchtung TFL mit Begrenzunglicht	Yes		Enable DRL with Markers On
Coding-Exterior lighting-DDL Specification		No		Disable DRL with Light Switch Off
Coding-Exterior lighting-Exterior lighting: SML flashes in sync	Aussenbeleuchtung SML mitblinkend	Yes		Enable side marker blinker with turn signal
Coding-General-Acoustic feedback for locking		Yes		Enable acoustic feedback on locking (No disables lock chirp)
Exterior lights parameters-One Touch flashing cycles		Number		Change number of One Touch Flashing Cycles (Default 3)
Extended Codings
Extended codings-FLA codings-High beam assistant (FLA) present		Yes		Enable High Beam Assist
Rear End Electronics	BCM ruck	Value	Related	Description
Codiertabelle
Exterior lighting
Exterior Lights, DD lights as marker light		Yes		Enable DRL 4-Point LED’s when headlights on
Exterior lights parameters
Dimming value for DD lights as marker light		100		Dimming value, set to 100 for full intensity
Instrument Cluster	Kombiinstrument	Value	Related	Description
Extended codings
Extended codings_0
Extended codings-Max. boost pressure	Weitere Codierungen: Max. Ladedruck	1.66	BAR	Raise max boost gauge reading to 24PSI (for aftermarket tunes)
Extended codings-Sport boost pressure	Weitere Codierungen: Ladedruck Sport	1.66	BAR	Raise max boost gauge reading to 24PSI (for aftermarket tunes)
Board computer display configuration key 1_0
BC Configuration byte 8-Door unlocking setting		On		Enables the unlocking of all doors with single press of keyfob
BC Configuration byte 9-locking-mirror fold-in		On		Auto fold mirrors when doors locked (requires additional coding)
BC Configuration byte 10-locking relocking time, after door unlocking		30		Change delay for the auto door re-lock if you unlock and don’t open a door (Max 90)
Board computer display configuration key 1_1	Bordcomputer Menukonfiguration
BC Configuration byte 4-BC Role G-Force	aktiv"}">Performance-Anzeige -> aktiv	On		Enable the G-Force menu (requires additional coding)
BC Configuration byte 13-high beam assistant		On		Enable High Beam Assist
BC Configuration byte 13-Performance Display	aktiv"}">Performance-Anzeige -> aktiv	On		Enable HP & Torque menu (requires additional coding)
BC Configuration byte 22-BC Role Performance Display		On		Enable HP & Torque menu (requires additional coding)
Board computer display configuration key 2_1
BC configuration byte 13 – high beam assistant		On		Enable High Beam Assist
Board computer display configuration key 3_1
BC configuration byte 13 – high beam assistant		On		Enable High Beam Assist
Board computer display configuration key 4_1
BC configuration byte 13 – high beam assistant		On		Enable High Beam Assist
Board computer display configuration factory setting
BC configuration byte 13 – high beam assistant		On		Enable High Beam Assist
Board computer menu configuration	Bordcomputer Menukonfiguration
Board computer menu configuration_0
Board computer menu configuration byte 0-boost pressure (bargraph)		Yes		Enable Boost Pressure Bargraph in Vehicle Menu
Board computer menu configuration byte 2-mirror fold-in	aktiv"}">Byte 2 Siegel einklappen -> aktiv	Yes		Auto fold mirrors when doors locked (requires additional coding)
Board computer menu configuration byte 4-expert menu		Yes		Enable the Expert menu (readout of engine sensors & running values)
Board computer menu configuration byte 4-G-Force	aktiv"}">Byte 4 G-Force -> aktiv	Yes		Enable the G-Force menu (requires additional coding)
Board computer menu configuration byte 7-Performance Display	aktiv"}">Auswahl Performance-Anziege -> aktiv	Yes		Enable HP & Torque menu (requires additional coding)
Board computer menu configuration 2_1
Board computer menu configuration 2 byte 2-Joker Sport		Yes		Enable Sport Mode activation with Diamond button
Board computer menu configuration 2 byte 2-Joker Sport exhaust		Yes		Enable Sport Exhaust activation with Diamond button
Board computer menu configuration 2 byte 0-high beam assistant		Actuated		Enable High Beam Assist
Warning lamps
indicator lamps coding-High beam assistant		On		Enable High Beam Assist
Dimming-general configuration	Dimmung – allegemeine Konfiguration
Configuration-All dials white	Konfiguration zentrales Zifferblatt Weiss	Yes	Code 1st	Enable backlight on RPM dial (value may also be Not Running)
	Konfiguration alle Zifferblatter Weiss	Yes	Code 2nd	Enable backlight on Speedometer dial (value may also be Not Running) – only if RPM dial enabled
Kodierwert
Kodierwert-Coding byte 2-Driver seatbelt warning		Deactivated		Disable seatbelt warning (Driver)
Kodierwert-Coding byte 2-Passenger seatbelt warning		Deactivated		Disable seatbelt warning (Passenger)
Kodierwert-Coding byte 2-USA seatbelt warning		Deactivated		Disable seatbelt warning LED
Kodierwert-Coding byte 2-Acoustic seatbelt warning		Deactivated		Disable seatbelt warning Chime
PCM	HeadUnit	Value	Related	Description
Coding value
Coding value_1
VW Coding Value Textual-Bit field (4)-byte_23_Initial Disclaimer		Off		For older models with PCM3, disable initial disclaimer
VW Coding Value Textual-Bit field (4)-byte_23_Legal Disclaimer		Off		For older models with PCM3, disable navigation disclaimer
PCM/CDR Automatic mirror fold in function		Yes		Add Mirror Retract in PCM 3.1
PCM/CDR Handset settings – Ring tone volume		%		Adjust ring volume from Default 50%
Driver-side Seat Memory		Value	Related	Description
Comfort Entry/Exit adjustment travel-E/A adjustment travel in		Number		Changes distance seat moves back in mm from driving position on entry. Default is "26”, I made it "40”.
seat fore/aft adjustment
Rear Lid	Heckdeckel	Value	Related	Description
System selection REAR LID, for both open and close	-> Change ms value to 0"}">Additional Options (F -> Change ms value to 0	Deactivated		Disable Hatch/Trunk open and close beeps
Set FFB,ST,FIT,HKIT to INACTIVE
Front Camera		Value	Related	Description
Coding	Kodierwert
Coding value-Lighting assistant coding	Bank 2-AFS_coding_Light_Assist	HBA		Enable High Beam Assist

 

Launch X431 is easier to use, but it does not have as much as coding functions than PIWIS. PIWIS has its specific uses. When you swap Macan headlights from BiXenon to LEDs, headlight commissioning and module coding can only be done with PIWIS. When replace air suspension compressor and rear suspension air bag, you can refill and recalibrate with PIWIS.

If you screw up coding with X431 and can’t go back, PIWIS module auto coding will fix it.

PIWIS language is set to German. Language in X431 for coding is English.

Launch X431is good for daily use and you also needPIWIS.

Posted by: jean at 06:32 AM | No Comments | Add Comment
Post contains 1052 words, total size 34 kb.

Lonsdor K518 Adds Mitsubishi 2019- Immobilizer

Lonsdor K518ISEandK518Sreleased new Mitsubishi software update in July 2023.

Update following models:

MITSUBISHI\Select from vehicle China Eclipse Cross\lmmobilizer 2019-

MITSUBISHI\Select from vehicle China Triton 2019- Immobilizer

MITSUBISHI\Select from vehicle China Triton 2019-Remote

MITSUBISHI\Select from vehicle China Lancer\Smart key

MITSUBISHI\Select from vehicle Asia OtheriDelica Smart key

MITSUBISHI\Select from vehicle Asia Other\L200\2015- Smart key

MITSUBISHI\Select from vehicle Asia Other M380lmrriobilizer CaN line

MITSUBISHI\Select from vehicle Asia Other M380\lmmobilizer\K line

MITSUBISHI\Select from vehicle Asia Other\Montero 2016-Smart key

MITSUBISHI\Select from vehicle Asia Other\Nativa lmmobilizer\2016-

MITSUBISHI\Select from vehicle Asia Other RVRSmart key

MITSUBISHI\Select from vehicle Asia Tapan\RVR\Smart key

MITSUBISHI\Select from vehicle Europe M380 immobilizeriCAN line

MITSUBISHI\Select from vehicle\Europe M380 immobilizer\K line

MITSUBISHI\Select from vehicle Europe Montero 2016-Smart key

MITSUBISHI\Select from vehicle Europe Space Star\2013-2014 Smart key

MITSUBISHI\Select from vehicle Europe Space Star 2015-Smart key

MITSUBISHI \Select from vehicle\Australia M380\lmmobilizer CAN line

MITSUBISHI\Select from vehicle Australia M380\lmmobilizer k line

MITSUBISHI\Select from vehicle America USARVR With smart

MITSUBISHI\Select from type Smart key\Type 5

Posted by: jean at 06:13 AM | No Comments | Add Comment
Post contains 162 words, total size 3 kb.

OBDSTAR iScan Ducati Motorcycle Software update to V31.50

OBDSTAR IScan DUCATImotorcycle released new software version V31.50.

The entire vehicle series is supported until October 2022.

Highlights Added

• A/F self-adaptive reset
• ABS setting in EOL mode
• ANNUAL SERVICE
• Annual service warning light deactivation
• Anti-theft enabling/disabling
• Bat. volt, history display
• Bat. volt, history reset
• Bluetooth enabling/disabling
• DESMO service light reset
• DQS adaptive reset
• DRL Daytime Running Light enabling/disabling
• Enable/disable DQS
• Exhaust valve calibration
• Exhaust valve system maintenance
• Fuel level value reset
• GPS enabling/disabling
• Heated grips enabling/disabling
• Idle control adaptive reset
• Idle speed engine operation mode
• Key reset
• Knock sensor adaptive reset
• Odometer writing (totalizer)
• OIL SERVICE
• OIL service light reset
• PIN code reset
• Reset gears
• Reset the adaptive values of the throttles in a completely closed position
• Reset the debug packages
• Reset the transmission adaptive values
• Reset self-adaptive A/F parameters
• Storing keys
• Suspension rotary sensor calibration (rear)
• Throttle balancing
• TPMS code writing
• TPMS Registration
• TPS adaptive reset
• VALVE CHECK
• Variation of the current date in the dashboard
• Variation of the current time in the dashboard
• Variation of the next annual service date
• Vehicle statistical data reset
• Version set in the BBS

Posted by: jean at 06:35 AM | No Comments | Add Comment
Post contains 231 words, total size 3 kb.

Will Autel IM608 Program 2022 Subaru Outback All Keys Lost

Autel supports all smart keys lost function forsome modelsas of 2022 Subaru Outback and Legacy with thelarge vertical dash screens.

Here is the user working experience on Outback 2020-2022 all keys lost programming:

1.

I was able to program a key using anAutel IM508along with anAPB112 smart keysimulator without replacing any parts. I now have a working key which should allow me to use other functions on the IM508 like removing the old keys.

The process is relatively easy. Using manual selection, pick your manufacturer, model, and year range from the menu. Find the Generate Analog Key option in the Immobilizer section and follow the on-screen steps; as long as it let’s you save the EEPROM data you should be good to proceed. Once that is done, it should direct you to connect the APB112 where it will create a simulated key. If that goes well, you can then use the Add Key prompt to create a new key (do not disconnect the APB112 during that process).

For reference, my vehicle is a 2020 Subaru Outback (NA) with the following part numbers:

SMT: 88801AN000
ESCL: 83126AN00B

2.

Posted by: jean at 06:42 AM | No Comments | Add Comment
Post contains 329 words, total size 3 kb.

How to Repair Porsche 12V battery by Launch X431 IMMO Plus

Launch X431 tablets supports Porsche Cayenne and Taycan 2018-2022 12V lithium battery repair. X-prog3 programmer is required. It comes in default withLaunch X431 IMMO EliteandIMMO Plus.

Here is an instruction to repair BMS on Cayenne with X431 IMMO Plus.

 

Go to Porsche Immobilizer software->BMS Repair->Cayenne-> 2018-2022

Connect x431 immo plus to G3

View wiring diagram

Remove the battery module, remove the case of the battery.
There is a SPC5644B processor in it that needs to be removed and repaired.

Connect battery module with g3 follow the wiring diagram

Choose Data recovery.
Writing completed. BMS reset is completed.

Posted by: jean at 07:04 AM | No Comments | Add Comment
Post contains 108 words, total size 8 kb.